Johnsonite 996 Two Part Epoxy Glue
Johnsonite 996 Two Part Epoxy Glue is a recommended adhesive when installing wheeled traffic transition strips. The Johnsonite 996 adhesive comes with 2 containers for a combined .92 Gallon: Part A and Part B.
- Shipping info
Website will only calculate shipping for the Contiguous US.
All other locations please call for shipping quote - 866-258-1554 - Payment methods
- Return Policy
We accept returns on most products that are not
custom made and are in resellable condition.
Johnsonite 996 Two Part Epoxy Glue
Johnsonite 996 two part epoxy glue is specially formulated for the installation of wheeled traffic transitions to clean dry porous or nonporous interior floor surfaces. This epoxy adhesive works great in areas were environmental and health concerns require an adhesive with environmentally sensitive characteristics. The Johnsonite 996 adhesive is solvent-free and contains no hazardous or carcinogenic ingredients. When purchasing this epoxy glue to install wheeled traffic transitions, you will receive 2 containers: part "a" and part "b".
Johnsonite 996 Adhesive Highlights
- Two part epoxy glue sold in 2 containers (part a and part b)
- Johnsonite 996 adhesive is solvent-free and contains no hazardous ingredients
- Shelf Life - 1 year at 70 degrees when stored in unopened, original container in dry area
- Open time - maximum open time is 40 to 50 minutes at 75 degrees or higher
- Coverage of two part epoxy glue is approximately 150 square feet
- Can be used on porous or nonporous substrates
- For interior use only
Lead time of the Johnsonite 996 two part epoxy glue will depend on stock (typically 1-3 weeks). Please call for availability.
Johnsonite adhesive can be used to install:
Johnsonite 996 Two Part Epoxy Glue Application Instructions for Wheeled Traffic Transitions:
- Mix all of part "B" into part "A" and mix thoroughly until smooth and uniform in color
- Mix for another 3-5 minutes. Adhesive will not cure if not properly mixed
- Immediately after mixing, apply to substrate using a 1/16 inch square-notched trowel
- Carefully position and install the molding. Use a J-Roller and hand roll the molding to ensure proper adhesive bond
- Avoid traffic for at least 12 hours after installation
- Avoid cold or excessive heat, including direct sunlight during installation
Two part epoxy glue cannot be removed when dry without damaging floor surface. Remove wet adhesive with a clean cloth dampened with Isopropanol, mineral spirits, or acetone.
Shipping Policy:
Available shipping options are shown in the table below. The Warehouse Rush option has been added due to customer demand.
Warehouse Rush means your order will take priority in the warehouse to ship out as soon as possible. Warehouse Rush fee varies according to product(s) ordered. Shipping fees will be calculated and shown once all items have been added to the cart and your shipping method has been selected.
| Shipping Type | Fee | Details |
| Standard Shipping | $7.99 | Order will be processed according to when submitted |
| Warehouse Rush | Variable Cost | Order takes priority in warehouse to ship ASAP |
| Overnight | Please contact for rates | 866.258.1554 608.244.1226 Sales@InstallerStore.com Monday - Friday 8am-5pm CST |
| Two Day | Please contact for rates | |
| Three Day Express | Please contact for rates | |
| Outside Contiguous US | Please contact for rates |
Standard Shipping and Warehouse Rush options will ship out ground USPS, FedEx, UPS, or Spee-Dee Delivery.
Orders with products that ship directly from the manufacturer or have longer lead times are not eligible for Warehouse Rush. Exceptions will only have the Standard Shipping option available.
Should any unexpected shipping delays arise and the order cannot be shipped via Warehouse Rush, you will be contacted and refunded the difference between Standard Shipping and Warehouse Rush fees.
Please call, toll free at (866) 258-1554 or our local number at (608)-244-1226, Monday through Friday, 8am-5pm CST or email for expedited, APO/FPO, or shipments outside Continental US. Please note customers are wholly responsible for these shipping fees.
Transit times can vary depending on destination. Orders are shipped Monday through Friday, with the exception of national holidays.
We accept the following payment methods:
You can also call us or mail in a check.
Payment must be made before items ship.
Please contact us immediately in the event an incorrect product has been sent or an order has been damaged in shipping. We will gladly remedy the situation at no extra cost to you.
Acquiring a Return Merchandise Authorization (RMA) Number:
Please call 866-258-1554 or email Sales@InstallerStore.com to receive a Return Merchandise Authorization number if there is any reason you would like to return your order. All charges to ship merchandise back are the responsibility of the customer. There will be a 10% re-stock fee on all returned orders, unless a replacement order has been made. Customers are given 7 days from the delivery date to contact us for a RMA number. Returns must be received back to our warehouse within 90 days. Fees may change based on extended time passing.
Returns of open/used products are not accepted.
Special order items are not returnable and are designated on the specific product pages.
Shipping charges are not refundable.
InstallerStore strongly encourages choosing a shipping method for your return where a tracking number and insurance can be obtained. Accounts will be credited back after inspection has been made to the product to ensure product has not been damaged in any way and can be resold. Packages damaged while being shipped back to us will not be accepted as a return and customer will be contacted. InstallerStore is not responsible for lost or damaged returns. It is the customer's responsibility to file a claim with the shipping company.
Any merchandise that is shipped back without a RMA number will have a minimum re-stocking fee of 25% of the product cost and shipping charges will not be refunded.
All returned products must be shipped directly to InstallerStore even if they were originally shipped from the manufacturer, unless otherwise told by InstallerStore. Shipping back to manufacturer may cause re-stocking fee to increase.